About
Contact Us
Sitemap
skip to main
|
skip to sidebar
Contact Us
Contact Form
Contact Us
Reviewed by
belajar koor
on
3:43 PM
Rating:
5
No comments:
Subscribe to:
Posts ( Atom )
Label
ASME
BS EN ISO 6520-1
burn-through
Cavities
Cavity
Chipping mark
Code & Standard
concavity
consumables
Convex
Cracks
Crater pipe
Dimensional survey
distortion
excess penetration
excess weld metal
fit up
fusion line
Gas Pore
gouging
grinding
Grinding mark
HAZ
Hydrogen induced cracks
Imperfect Shape
inter-run
interpass
ISO 15607
ISO 6947
ISO 9692
Lack of Fusion
Lack of Penetration
Lamellar tearing
material
misalignment
Miscellanous Imperfection
NDT
overlap
parent metal
Porosity
preheat
pressure test
PWHT
repairs
root
site
Solid Inclusions
solidification cracks
Spatter
Stray arc
Temper colour
toe
Torn surface
Undercut
Underflushing
weld metal
Welder
welder test
Welding Joint
Welding Position
welding process
Worm holes
WPS
Blog Archive
▼
2016
(16)
▼
June
(10)
Miscellaneous imperfections according to BS EN ISO...
Imperfect Shape and Dimensions according to BS EN ...
Definition and Types of Lack of Fusion and Penetra...
ASME BPVC Certification Symbol
ASME Single Certification Mark (New Stamp)
Definition and Types of Solid Inclusion according ...
Definition and Types of Cavities according to BS E...
Definition and Types of Cracks according to BS EN ...
Welding Imperfections according to BS EN ISO 6520-1
Types of Welding Preparation Refer to Standard BS ...
►
May
(6)
Recents
Popular
Definition and Types of Cracks according to BS EN ISO 6520-1
Crack is imperfection produced by a local rupture in the solid state, which may arise from the effect of cooling or stresses. Cracks are ...
Definition and Types of Cavities according to BS EN ISO 6520-1
Cavities , is imperfection formed by entrapped gas, and also caused by shrinkage during solidification. Types of cavities: Gas Pore ...
Welding Imperfections according to BS EN ISO 6520-1
Definitions: Imperfection Any deviation from the ideal weld. Defect An unacceptable imperfection. BS EN ISO 6520-1 standard ...
Imperfect Shape and Dimensions according to BS EN ISO 6520-1
Types of Imperfect Shapes and Dimensions : Undercut An irregular groove at the toe of a run in the parent metal or previously deposit...
Definition and Types of Lack of Fusion and Penetration according to BS EN ISO 6520-1
Lack of fusion is lack of union between the weld metal and the parent metal or between the successive layers of weld metal. Types of lack ...
Definition and Types of Solid Inclusion according to BS EN ISO 6520-1
Solid inclusions is solid foreign substances trapped in the weld metal. Types of solid inclusions: Slag inclusions Slag trapped duri...
Types of Welding Preparation Refer to Standard BS EN ISO 9692
Open Square Butt Preparation Used for welding thin components from one or both sides. If the root gap is zero (ie if components are in c...
Miscellaneous imperfections according to BS EN ISO 6520-1
Types of m iscellaneous imperfections: Stray arc (arc strike) Local damage to the surface of the parent metal adjacent to the weld, r...
Welding Position ( according to ISO 6947)
Flat Position (PA). Welding position in which the welding is horizontal with the centreline of the weld vertical. Horizontal...
Welding Joint (according to BS EN ISO 15607)
Butt Joint Connection between the ends or edges of two parts making an angle to one another of 135-180° inclusive in the region of the...
Comments
Powered by
Blogger
.
No comments: